36V 750W 48V 1000W 48V 1500W Powerful 26x4.0" Fat Wheel Rear Motor Wheel eBike Conversion Kits
36V 750W / 48V 1000W / 36V 1200W / 48V 1500W 26x4.0" Motorized Fat Rear Wheel with Shimano 7-speed freewheel
36-72V 45A Sine Wave Controller 12 MOSFET
TFT750C or UKC-1 Color Display (Randam delivery, if you have special requirement, please write remark after you order it)
Half-bar Twist Throttle with Lock
RM-D700 hydraulic disc brakes (Front and Rear)
PAS Pedal Assistant Sensor
Bluetooth Module (for controller parameter setting)
Power supply Cable
1) High Motor Efficiency: max 88.7% (Save Power)
2) Torque: max torque 40 N.m.
3) RPM: max 497.5
4) Speed: 0-58 km/h (different wheel size, road & weather condition and rider's weight will have different speed)
5) Hub Width (dropout): 175mm or 190mm rear thread-on hub motor
6) Support standard 6-hole type disc brake
7) Rear Wheel with 7-speed Shimano freewheel
1) Does your rear wheel support disc brake?
Yes, our motor wheel support standard 6-hole type disc brake. If you want to install hydraulic disc brake, we recommend you to put a 5mm washer between disc brake rotor and motor (to add distance between motor and rotor to put thicker caliper)
2) Why can't turn on power
Please kindly check whether battery poles connect with controller is correct;
Please kindly check whether all connection correct and tight
Please kindly check whether you connect electric lock plug and turn on throttle key
Please kindly check whether you turn on LCD Display
3) Why after I turn on power and turn throttle, motor doesn't work
Please kindly check whether all power already turned on
Please kindly check whether throttle connection is correct (Throttle is Red/Back/Blue wires)
Please kindly check PAS speed level on LCD, whether it is not 0 (0 will turn off PAS and throttle)
4) Why my speed display is not correct
Please kindly check whether you have correct setting:
Correct wheel size setting: according to your wheel size
Correct magnet pair setting: set it as 23
5) Why always cut off during riding
Please kindly check whether your battery support enough discharge current (Battery has enough capacity and Battery BMS board support max continuous discharge current at 40A)
Please check whether controller MOSFET is burned and short circuit
6) How can I active cruise function
If your controller connect LCD display, please don't plug the jumper on cruise connector: SM-2Y Female Black Connector with Black/Blue wires
Please set C7=1 from LCD, save and restart LCD
With hold throttle and keep definite speed not change, press "Down" key of LCD display Button 3 seconds at same time, cruise function is activated. Any other operation will cancel cruise function.
How to disable cruise function: To set C7=0 save and restart will disable cruise function again.
If your controller doesn't connect LCD display, please plug the jumper on cruise connector: SM-2Y Female Black Connector with Black/Blue wires
When hold throttle and keep definite speed not change about 3 seconds, cruise function is activated. Any other operation will cancel cruise function.
How to disable cruise function
Please turn on power
Please remove cruise plug (small black plug of Black/Blue wires)
Turn off power
Turn on power again
7) Why after turn on, LCD show "03_Info"
This is because of hall sensor abnormal, and most time is because hall sensor wires connection doesn't contact well, please kindly check the 5-wire hall sensor connector and also inside whether any pin bent doesn't contact well. If use quick release wire, please kindly check whether connector plugged very tight. If every connection is ok, then the most possible reason is hall sensor burned. (Very important: during installation, if need to remove the white hall sensor plug, please don't let hall sensor connector terminal touch phase connector terminal, otherwise hall sensor is very easy to be burned)
10) Which battery shall choose
You can choose 36V/48V Battery (full charged voltage shall be maximal 43.8/58.4V), Battery capacity best should be more than 15AH, battery and battery BMS board must support max continuous discharge current at 45A, otherwise battery will always cut off!