36V 48V 60V 72V 1100W-2200W 45A Ebike Programmable Intelligent Sine Wave Controller
1. 12 MOSFET 45A 36V, 48V, 60V, 72V Universal Voltage 1100W-2200W Intelligent Programmable Sine Wave Controller
2. USB Data Cable (to connect controller with computer to change setting)
1. 36V, 48V, 60V, 72V TFT750C Colorful Display (with 5-level PAS, Speed Limit, Speed Display, Voltage Selection, Start Mode, Regenerative Braking Function)
2.Bluetooth Module (can connect mobile phone and change setting via mobile phone App)
- Programmable Sine Wave Controller which support big current and smart match with each motor through self-learning, works with high efficiency, less noise, and lower energy consumption, which makes your electric vehicles or electric motorcycles more comfortable and easier to control, give you best pedal experience
- Motor torque ripple is reduced to minimum through FOC, more smooth and comfortable
- Universal Input Voltage Range: 36V/48V/60V/72V
- Work with or without display
- Parameter setting via Mobile Phone App or Computer
- All protection make it long life and safe: over/under voltage, over current, over load, over heating, anti-runaway, locked-motor protection
- Multi functions: Smart match with different motor, 5-speed level for throttle and PAS, Speed limit, reverse, anti-thief, Regenerative Braking, Electric Braking, Keyless start and etc.
- Best heat sinking with thicker Heat sink Aluminium Plate
- Anodized Aluminium Controller Case against scratch
- Power supply: 36V/48V/60V/72V, MAX DC current: 45A, Max phase current: 70A
- Rated Power: 36V 1100W/ 48V 1500W/ 60V 1900W/ 72V 2200W
- Peak Power: 36V 1600W/ 48V 2100W/ 60V 2700W/ 72V 3200W
- Low Voltage Protection: 30V/40V/50V/60V
- Brake: Low Voltage Brake
- Alarm: Low Voltage Alarm
- Rotor Position Detecting Method: Hall sensor
- Mobile phone App or computer software can communicate with the controller to modify parameter
- Size: 180x99x65mm
- Net Weight: 1.1 kgs
- Waterproof Grade: IP65
RisunMotor programmable sine-wave motor controller works with high efficiency, less noise, and lower energy consumption, which makes your electric vehicles or electric motorcycles more comfortable and easier to control. Our designed friendly interface of the programmable motor controller makes you set the parameters, conduct the tests and obtain the diagnostic info easily and quickly.
- FOC-180° sinusoidal drive controller applied to BLDCM or PMSM.
- It takes only 2-3 minutes for the motor to be well matched on its best electronic angle at the first time.
- The motor torque ripple will be reduced to the minimum, so as to ensure electric vehicle to run without any noise and vibration, smoothly, and comfortably.
- The precise current ring can provide accurate torque input to meet the requirement of large torque output during vehicle starting and climbing.
- The controller enjoys high efficiency due to space vector converter control algorithm which can effectively reduce the temperature rise of controller and extend battery life mileage
- Built-in various protection: locked-rotor protection, over-current protection, overload protection, over-temperature protection, speed protection, over-voltage protection, under-voltage protection and so on, effectively ensuring the safety of electronic control system and vehicle.
- System status and fault intelligent management system can effectively monitor the current system operating mode external input state, the case of system failure, and the LED flashes at the same time to facilitate the diagnosis and maintenance.
- Multi peripheral interfaces: reverse, cruise, anti-theft electronic brake, etc.
- Parameter modifications and settings are available through Mobile phone via Bluetooth or computer via USB data cable
- CAN BUS is optional to communicate with body instrument and BMS
1. Can I use this controller without display?
Yes, you can use this controller without display, just need to connect jumper connector (Please check Controller Connection Diagram, Page 3, point No.5)
2. Why when I turn on Display, it always show "Error 30H"?
Please kindly check whether you also connect communicaton plug (Please check Controller Connection Diagram, Page 6, point No.12)
3. Why when I connect Bluetooth Module or USB Cable, it always show "Connection Failure"?
Please kindly check whether you disconnect communicaton plug (Please check Controller Connection Diagram, Page 6, point No.12), and also reconnect Bluetooth Module or USB Cable to ensure good connection.
4. If I want to use your controller work with my motor, what shall I do?
Manual and Driver Program Download:
2. Controller USB Connection Driver, Application Program and Manual (Controller connect with computer by USB Cable)
(1). USB Driver Download:
3. Controller Manual/ Bluetooth App Manual (Controller connect with mobile phone by Bluetooth Module)